Welcome to DGI

CURVED LAMINATE BENCHTOPS

Not only the natural warmth of timber, but soft, sensuous curves as well.


Jarrah curved laminate bartop

The DGI Queensland plant has for many years specialised in the manufacture of benchtops incorporating curved laminates. Working to a specified radius, or even an 'S' shaped curve, DGI can determine the laminate size necessary to be able to bend the individual strips of timber and glue them to a pre-determined shape.

As the bending of timber is an inexact science, it is always preferable to work to a full size template so that accuracy can be maintained. Such accuracy to radius must be within certain limits as there will be inevitable 'espring' when the cured top is released from the clamps, and even with the most accurate calculations, variations in species density and even within species can create differing amounts of spring. However, many tops have been manufactured to specific criteria over the years, and DGI have gained the mastery necessary to manufacture a product suitable for all aesthetic, practical and architectural purposes.

The various steps in the manufacture of a curved laminate top are relatively simple in outline, but any errors in either calculation, knowledge of species characteristics, or manufacturing processes, will mean that the finished product does not conform to the required or specified radius.

The manufacture of curved DGI Glulam requires similar equipment levels, expertise and attention to quality as straight Glulam (see leaflet #9) but with the added difficulties associated with bending timber.

1. Determining the Laminate Size

The successful bending of timber necessitates a laminate width that will conform to the required radius. The tighter the radius required, the thinner the lam. width needs to be. Sometimes the lam. width needs to be reduced in order to gain sufficient laminations so that the curve will hold its shape. This is particularly so with narrow members such as handrails or shelving. Having close to 25 years experience in bending various timbers, DGI Qld. has a large data-base matching each timber species to varying curve radii.

Very small radii (less than 1500m) can be untenable, as the laminate size may become too thin to look appealing. Each species, dependant on its density and bending qualities, will, of course, vary in the determined laminate size.


Forest Lake Tavern, Brushbox

2. Manufacturing a Curved Clamping Jig

Each job is generally a "one-off", ie. it is unlikely that more than one job will have the same radius, the same width or the same length. Therefore, a clamping jig needs to be made specifically for each job. Jigs are out-sourced from specialist engineers and are designed specifically for each project. On receipt of the jig it is checked for accuracy and strength by DGI quality control.

(Pic. right: Laminate preparation)

3. Preparation for Clamping


Timber & glue selection, ripping to size, fingerjointing, machining, sorting - pre-conditioning and glue spreading are exactly the same as for straight Glulam and a full explanation is provided in Leaflet #9.

With the large number of laminates often found in curved Glulam, it becomes essential to have the laminates accurately machined. Firstly for the sizing they may have to match up to another run. Secondly for correct machine grade on the face, so that the glue penetration will be correct for that species.

(Pic. left: Glue spreading)


Preparing the first clamp

4. Pressing


Tamping the laminates prior to
final tightening

(Pic. right: Clamping finished -curing in process)

Unlike straight Glulam where many boards are glued at the same time, with curved Glulam only one board can be glued at a time in the one jig.

The curved glue-bed consists of specially designed trestles spaced and set so as to allow the operator to walk between them. The steel jig is placed on the bed and the pre-glued laminates are laid out behind the jig with the middle of the laminates touching the rise of the jig. The clamps are then placed in position at predetermined spacing points. The clamps are then tightened starting from the centre and working alternately to the ends. As the clamps tighten the laminates are drawn towards the jig where they are held until curing has occurred.


5. Planing / Sanding

Finishing is by a 130Omm wide combination planer/sander. Curved benchtops with a rise too wide for the machine may have to be made in two sections and joined after finishing. Integral aprons or splashbacks are also glued on afterfinishing.

(Pic. right: Through the planer/sander)


6. Testing

DGI care about quality and conduct the same rigorous series of tests on curved Glulam as they do with straight Glulam. These tests are all outlined in Leaflet # 9.

(Pic. right: Packed & ready for shipment)

7. Warranty

Curved DGI Glulam carries the same warranty as straight DGI Glulam, ie. DGI guarantee against manufacturing defects which could render the product unserviceable or unfit for normal usage for five years. All we ask in return is that sealing, installation and care instructions are adhered to, and that the product is not used in areas of extreme climatic conditions. Our warranty does not cover external use, as our products are specifically designed for internal use.

Natural variations in colour or texture of wood are not considered defects, and minor improvements to knots, shakes or gum veins by filling are part and parcel of thejoy of living with timber.

8. Design

Almost any design can be accomplished using DGI curved Glulam. From a simple radius, to parabolic or multiple curves. Varying widths, long lengths even integral aprons or splashbacks. There are of course some limitations such as very tight radii, but our experts can advise on the best alternatives.

Curved Laminate Benchtops
Simple Curve
Curved Laminate Benchtops
Parabolic Curve
Curved Laminate Benchtops
Double Curve
Curved Laminate Benchtops
Curve with Splashback
Curved Laminate Benchtops
Curve with Apron
Curved Laminate Benchtops
Varying width Curve

9. What We Need to Know

Always providing a template is best policy.

We work from the INSIDE radius so please provide this. We can, of course, calculate the IR if we are provided withthe Length and Rise or the Outside radius.

Curved Laminate Benchtops

America's Cup Bar - Sydney Hilton

For complex designs and where accuracy is critical a template is absolutely essential.

Remember curving is not an exact science. Even though we allow for the expected spring, minor density variations can alter the radius slightly. Also a small difference in measurements at one point can mean a larger difference some metres away at the other end. Supply a template and DGI will produce a product to match the template. Alternatively let DGI make the benchtop first and then you can use it as the template for the carcase.

 

Site designed & maintained by Spec-Net Pty Ltd